Paradox spectra 1728 installation manual

Spectra 1727 User Manual - SECURUS 1728EX, 1728, 1738EX AND 1738 SYSTEM PROGRAMMING GUIDE Software Version 2.1 DEFAULT INSTALLER CODE (see section [281] on page 18) DEFAULT SYSTEM MASTER CODE (see section [301] on page 18) HOW DO I ENTER PROGRAMMING MODE? When key [1] is ON (illuminated), the keypad s zone is Keypad Zone 2. Event # Sub- # 00 = Zone OK 01 to 16 = Zones 1 to = Any Zone 01 = Zone Open 01 to 16 = Zones 1 to = Any Zone 02 = Partition Status 00 = System not ready (Partition 1 only) 01 = System ready (Partition 1 only) 02 = Steady Alarm in Partition 03 = Pulsed Alarm in Partition 04 = Pulsed or Steady Alarm in Partition 05 = Alarm in Partition Restored 06 = Bell Squawk Activated (Partition 1 only) 07 = Bell Squawk Deactivated (Partition 1 only) 08 = Ground start (Partition 1 only) 09 = Disarm Partition 10 = Arm Partition 11 = Entry Delay (breach when system is armed) 99 = Any Sub- 05 = Non-Reportable Events 00 = Telephone Line Trouble (Partition 1 only) 01 = [PG] or [FNC1] key was pressed (Partition 1 only) 02 = Instant Arming 03 = Stay Arming 04 = Force Arming 05 = Fast Exit (Force & Regular Only) 06 = PC Fail to Communicate (Partition 1 only) 07 = Midnht (Partition 1 only) 99 = Any Sub- (Partition 1 only, except 02 to 05) 06 = Arm/Disarm with Remote Control 01 to 08 = Remote Controls 1 to 8 99 = Any Remote Control 07 = Button Pressed on Remote 01 to 08 = Remote Controls 1 to 8 (see button option B on page 26) 99 = Any Remote Control 08 = Button Pressed on Remote 01 to 08 = Remote Controls 1 to 8 (see button option C on page 26) 99 = Any Remote Control Spectra 1728/EX & 1738/EX Programming Guide 09 = Button Pressed on Remote (see button option D on page 26) Event # Sub- # 01 to 08 = Remote Controls 1 to 8 99 = Any Remote Control 10 = Bypass Programming 01 to 48 = User Code Numbers 001 to = Any User Code 11 = User Activated PGM 01 to 48 = User Code Numbers 001 to 048 (Partition 1 only) 99 = Any User Code 12 = Zone with Delay Transmission Option Enabled is Breached 01 to 16 = Zones 1 to = Any Zone 13 = Arm with User Code 01 to 48 = User Code Numbers 001 to = Any User Code 14 = Special Arm 00 = Auto Arming (timed/no movement) 01 = Late to Close (Auto-Arming failed) 02 = No Movement Auto-Arming 03 = Partial Arming (Stay, Force, Instant, Bypass) 04 = One-Touch Arming 05 = Arm with Win Load Software 99 = Any Sub- 15 = Disarm with User Code 01 to 48 = User Code Numbers 001 to = Any User Code 16 = Disarm After Alarm w/ User Code 01 to 48 = User Code Numbers 001 to = Any User Code 17 = Cancel Alarm with User Code 01 to 48 = User Code Numbers 001 to = Any User Code 18 = Special Disarm 00 = Cancel Auto Arm (timed/no movement) 01 = Disarm with Win Load Software 02 = Disarm after alarm with Win Load Software 03 = Cancel Alarm with Win Load Software 99 = Any Sub- 19 = Zone Bypassed on Arming 01 to 16 = Zones 1 to = Any Zone 20 = Zone in Alarm 01 to 16 = Zones 1 to = Any Zone 21 = Fire Alarm 1728/EX: 01 to 05 = Zones 1 to 5 (on-board inputs) 1738/EX: 01 to 07 = Zones 1 to 7 (on-board inputs) 99 = Any Zone 22 = Zone Alarm Restore 01 to 16 = Zones 1 to = Any Zone 23 = Fire Alarm Restore 1728/EX: 01 to 05 = Zones 1 to 5 (on-board inputs) 1738/EX: 01 to 07 = Zones 1 to 7 (on-board inputs) 99 = Any Zone 24 = Special Alarm 00 = Emergency Panic 01 = Auxiliary Panic 02 = Fire Panic 03 = Recent Closing 04 = Auto Zone Shutdown 05 = Duress Alarm 06 = Keypad Lockout 99 = Any Sub- 25 = Auto Zone Shutdown 01 to 16 = Zones 1 to = Any Zone 26 = Zone Tamper 01 to 16 = Zones 1 to = Any Zone 27 = Zone Tamper Restore 01 to 16 = Zones 1 to = Any Zone Spectra 1728/EX & 1738/EX Programming Guide Event # Sub- # 28 = System Trouble 01 = AC Loss: only after Power Failure Delay has elapsed (Partition 1 only) 02 = Battery Failure (Partition 1 only) 03 = Auxiliary current overload (Partition 1 only) 04 = Bell current overload (Partition 1 only) 05 = Bell disconnected (Partition 1 only) 06 = Timer Loss (Partition 1 only) 07 = Fire Loop Trouble (Partition 1 only) 08 = Future Use 09 = Module Fault (Partition 1 only) 10 = Printer Fault (Partition 1 only) 11 = Fail to Communicate (Partition 1 only) 99 = Any Sub- (Partition 1 only) 29 = System Trouble Restore 00 = TLM restore (Partition 1 only) 01 = AC Loss restore (Partition 1 only) 02 = Battery Failure restore (Partition 1 only) 03 = Auxiliary current overload restore (Partition 1 only) 04 = Bell current overload restore (Partition 1 only) 05 = Bell disconnected restore (Partition 1 only) 06 = Timer Programmed (Partition 1 only) 07 = Fire Loop Trouble restore (Partition 1 only) 08 = Future Use 09 = Module Fault restore (Partition 1 only) 10 = Printer Fault restore (Partition 1 only) 11 = Fail to Communicate restore (Partition 1 only) 99 = Any Trouble Restore (Partition 1 only) 30 = Special Reporting 00 = System Power Up (Partition 1 only) 01 = Test Report (Partition 1 only) 02 = Win Load Software Access (Partition 1 only) 03 = Win Load Software Access finished (Partition 1 only) 04 = Installer enters programming mode (Partition 1 only) 05 = Installer exits programming mode (Partition 1 only) 99 = Any Sub- (Partition 1 only) 31 = Wireless Transmitter Supervision Loss 01 to 16 = Zones 1 to = Any Zone 32 = Wireless Transmitter Supervision Loss Restore 01 to 16 = Zones 1 to = Any Zone 33 = Arming with a Keyswitch 1728/EX: 01 to 05 = Zones 1 to 5 (on-board inputs) 1738/EX: 01 to 07 = Zones 1 to 7 (on-board inputs) 99 = Any Zone 34 = Disarming with a Keyswitch 1728/EX: 01 to 05 = Zones 1 to 5 (on-board inputs) 1738/EX: 01 to 07 = Zones 1 to 7 (on-board inputs) 99 = Any Zone 35 = Disarm after Alarm with a Keyswitch 1728/EX: 01 to 05 = Zones 1 to 5 (on-board inputs) 1738/EX: 01 to 07 = Zones 1 to 7 (on-board inputs) 99 = Any Zone 36 = Cancel Alarm with a Keyswitch 1728/EX: 01 to 05 = Zones 1 to 5 (on-board inputs) 1738/EX: 01 to 07 = Zones 1 to 7 (on-board inputs) 99 = Any Zone 37 = Wireless Transmitter Low Battery 01 to 16 = Zones 1 to = Any Zone 38 = Wireless Transmitter Low Battery Restore 01 to 16 = Zones 1 to = Any Zone Event # Sub- # Partition # 80 = PGM follows Clock (APR3-PGM4 only) HH = hour according to 24hr. clock Spectra 1728/EX & 1738/EX Programming Guide SYSTEM OPTIONS Bold = Default Setting SECTION [126]: General Options Option OFF ON [1] Confidential Mode Disabled Enabled [2] To Exit Confidential Mode Enter Access Code Press a Key [3] Confidential Mode Timer 2 minutes 5 seconds [4] PGM1 Normal State Normally Open (N. C.) [5] PGM2 Normal State (1738EX and 1738 only) Normally Open (N. SECTION [127]: General Options Option OFF ON [1] Partitioning Disabled Enabled [2] Access Code Length 6-dits 4-dits [3] Keypad Audible Trouble Warning Disabled Enabled [4] Lock System Master Code Disabled Enabled [5] Battery Charge Current 350m A 700m A [6] User Code 048 is a Duress Code Disabled Enabled [7] Alarm Relay follows (1738EX and 1738 only) Bell Output Global PGM [8] Future Use N/A N/A SECTION [128]: General Options Option OFF ON [1] Panic 1: Keys [1] & [3] Disabled Enabled [2] Panic 2: Keys [4] & [6] Disabled Enabled [3] Panic 3: Keys [7] & [9] Disabled Enabled [4] Panic 1: Silent or Audible Silent Audible [5] Panic 2: Silent or Audible Silent Audible [6] Panic 3: Silent or Fire Silent Fire [7] Keypad 1 Tamper Supervision Disabled Enabled [8] Keypad 2 Tamper Supervision Disabled Enabled SECTION [129]: General Options Option OFF ON [1] PGM2 Output Activation Option * Steady Pulse (flash) [2] PGM2 Pulse Once Every 30sec if System Armed * Disabled Enabled [3] PGM2 Pulse On Arm, Twice On Disarm * Disabled Enabled [4] ZX4 & ZX8 Zone Expansion Module Supervision Disabled Enabled [5] Wireless Module Supervision Disabled Enabled [6] Wireless Module Low Battery Supervision Disabled Enabled [7] 4-Output Bus Module Supervision (APR3-PGM4) Disabled Enabled [8] Printer Module Supervision (APR3-PRT1) Disabled Enabled * for 1738EX and 1738 only Spectra 1728/EX & 1738/EX Programming Guide Bold = Default Setting SECTION [130]: Arming/Disarming Options Option OFF ON [1] One-Touch Regular Arming* Disabled Enabled [2] One-Touch Stay Arming* Disabled Enabled [3] One-Touch Force Arming* Disabled Enabled [4] One-Touch Bypass Programming* Disabled Enabled [5] Restrict Arming on Battery Failure Disabled Enabled [6] Restrict Arming on Tamper Failure Disabled Enabled [7] Bell Squawk on Arm/Disarm with Keypad Disabled Enabled [8] Beep on Exit Delay Disabled Enabled SECTION [131]: Arming/Disarming Options Option OFF ON [1] Report Disarming Always Only after alarm [2] Regular Arming Switches to Force Arming* Disabled Enabled [3] Bell Squawk on Arm/Disarm with Remote Control Disabled Enabled (must be enabled for UL installations) [4] No Exit Delay When Arming with a Remote Control Disabled Enabled [5] No Exit Delay Beeps and No Bell Squawk When Disabled Enabled Stay Arming [6] Restrict Arming On Wireless Transmitter Disabled Enabled Supervision Loss [7] Generate Supervision Loss if Detected on Yes No Bypassed Wireless Zone [8] Future Use N/A N/A SECTION [132]: Zone Options Option OFF ON [1]&[2] see table see table Tamper Recognition Options see table see table [3] Generate Tamper if detected on Bypassed Zone Yes No [4] EOL (end-of-line) Resistors No EOL Use EOL Resistors [5] ATZ Zone Doubling (17 only) Disabled Enabled [6] Report Zone Restore On Bell Cut-off On Zone Closure [7]&[8] [1] [2] OFF OFF Disabled (default) OFF ON When disarmed: GENERATES TROUBLE ONLY When armed: Follows Zone Alarm Types ON OFF When disarmed: GENERATES SILENT ALARM When armed: Follows Zone Alarm Types ON ON When disarmed: GENERATES AUDIBLE ALARM When armed: Follows Zone Alarm Types Wireless Transmitter Supervision Options [7] [8] OFF OFF Disabled (default) OFF ON When disarmed: GENERATES TROUBLE ONLY When armed: Follows Zone Alarm Types ON OFF When disarmed: GENERATES SILENT ALARM When armed: Follows Zone Alarm Types ON ON When disarmed: GENERATES AUDIBLE ALARM When armed: Follows Zone Alarm Types see table see table see table see table * Not to be used with UL installations. More information System Introduction S E C T I O N 1 1.1 Specifications Downloading Software Support PC1555 uses DLS-1 v6.3 and up Flexible Zone Confuration Six fully programmable zones; system expandable to eht zones More information TM SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS Quick Start Instructions Introduction Win Load for Windows was developed to simplify and speed up the task of programming Paradox control panels. System from Paradox Security Systems. Panel, one Spectra Keypad, and various devices such. manual carefully and have your installer explain basic.

Paradox SPECTRA SP4000 Manuals STEP 1: Press [ENTER] STEP 2: Enter your [INSTALLER CODE] STEP 3: Enter 3-dit [SECTION] you wish to program STEP 4: Enter required [DATA] DECIMAL AND HEXADECIMAL PROGRAMMING TABLE Value or Action What Do I What Do I See? 10-Zone LED 16-Zone LED LCD Values 1 to 9 [1] to [9] [1] to [9] [1] to [9] [1] to [9] A (hexa only) [0] [0 (10)] [10] 0 B (hexa only) [STAY] [STAY] [11] B C (hexa only) [BYP] [BYP] [12] C D (hexa only) [MEM] [MEM] [13] D E (hexa only) [TBL] / [TRBL] [TBL] [14] E F (hexa only) [PG] / [FNC1] [PG] [15] F Exit Without Saving [CLEAR] [ENTER] flashes [ARM1] & [STAY1] flash SECTION [ ] Erase Current Dit [FORCE] Displays next dit or next section Save Data (hexa only) [ENTER] Advances to the next section TROUBLE DISPLAY Press the [TBL] or [TRBL] key to view the Trouble Display. Spectra 1728/EX & 1738/EX Programming Guide TABLE OF CONTENTS DEFAULT INSTALLER CODE... Key [1] OFF - Keypad Zone 1 (default) Key [1] ON - Keypad Zone 2 Key [2] - EOL Definition Key [2] determines the keypad zone s EOL definition. Spectra 1728/EX & 1738/EX Programming Guide Bold = Default Setting SECTION [133]: Partition 1 Options Option OFF ON [1] Auto-Arm on Time Disabled Enabled [2] Auto-Arm on No Movement Disabled Enabled [3] Auto Arming = Regular or Stay* Regular Arming Stay Arming [4] Switch to Stay Arming if no entry delay is opened Disabled Enabled [5] Stay Arming with Delay Partition 1 (Delay = [070]) Disabled Enabled [6] Future Use N/A N/A [7] Future Use N/A N/A [8] Future Use N/A N/A SECTION [134]: Partition 2 Options Option OFF ON [1] Auto-Arm on Time Disabled Enabled [2] Auto-Arm on No Movement Disabled Enabled [3] Auto Arming = Regular or Stay* Regular Arming Stay Arming [4] Switch to Stay Arming if no entry delay is opened Disabled Enabled [5] Stay Arming with Delay Partition 2 (Delay = [070]) Disabled Enabled [6] Future Use N/A N/A [7] Future Use N/A N/A [8] Future Use N/A N/A SECTION [135]: Dialer Options Option OFF ON [1]&[2] see table see table Telephone Line Monitoring (TLM) Options see table see table [1] [2] OFF OFF TLM Disabled (default) OFF ON TLM generates a trouble if armed ON OFF TLM generates an audible alarm if armed ON ON Silent alarms become audible [3] Reporting (Dialer) Disabled Enabled [4] Dialing Method Pulse Dialing Tone (DTMF) Dialing [5] Pulse Ratio 1:2 1:1.5 [6] If armed, activate bell output on Com. Paradox SPECTRA SP4000 Reference & Installation Manual 69 pages. Advanced Technology Zone atz Connections

GSM module G10 - Alarec Key [1] - Keypad Zone Selection Key [1] determines whether the keypad s zone is Keypad Zone 1 or Keypad Zone 2. Example: section [120] = : this means PGM1 will activate whenever partition 2 is Stay Armed. C.) [7] Reassn Keypad Zone 2 Disabled Enabled [8] Reassn Zones to Expansion Inputs* Disabled Enabled (1728EX and 1728 only) * Reassn Zones to Expansion Inputs changes the zone numbering to increase the number of expansion inputs that can be displayed on 10-Zone LED Keypads. According to its orinal purpose, user manual and relevant electronic and cal. When connected to a DSC, Caddx, Paradox or Pyronix security control panel data bus, the. SPECTRA SP5500, SP6000, SP7000, 1727, 1728, 1738.

Paradox spectra 1738 user manual - download torrents file 4 CONFURING THE 1686H, 1686V AND 1689 KEYPADS (PRIOR TO V2.0)... CONFURING THE 1686H, 1686V and 1689 KEYPADS (V2.0 or hher) The keypad s zone number, EOL definition and tamper switch are programmed through the keypad s programming mode. STEP 1: Press [ENTER] STEP 2: Enter your [INSTALLER CODE] (default: ) STEP 3: Press the [PG] (1686H/V) / [FNC1] (1689) key and hold it for 3 seconds. See below) STEP 5: Press [ENTER] to exit programming mode PLEASE NOTE: After two minutes, the keypad exits programming mode. [087] / / days (000 = disabled) AUTO TEST REPORT Disabled [088] / / 000 to 127 = 1 to 127 seconds CLOCK ADJUST Disabled 128 to 255 = -1 to -127 seconds [089] / / (000 = disabled, maximum = 15) AUTO ZONE SHUTDOWN COUNTER 5 [090] / / minutes (000 = disabled) RECYCLE ALARM DELAY Disabled [091] / / (000 = disabled) RECYCLE ALARM COUNTER Disabled [092] / / attempts before locking (000 = disabled) KEYPAD LOCKOUT Disabled [093] / / minutes (000 = disabled) KEYPAD LOCKOUT DELAY Disabled [094] / / seconds (000 = disabled) PANIC LOCKOUT TIMER Disabled [110] / : / hours (00 to 23) : minutes (00 to 59) AUTO TEST REPORT (TIME OF DAY) Disabled [111] / : / hours (00 to 23) : minutes (00 to 59) AUTO-ARM TIME (PARTITION 1) Disabled [112] / : / hours (00 to 23) : minutes (00 to 59) AUTO-ARM TIME (PARTITION 2) Disabled * Maximum 60 seconds for UL listed systems. Spectra 1728/EX & 1738/EX Programming Guide PROGRAMMABLE OUTPUTS Each PGM Deactivation event can be used as another start (activation) event if their respective PGM timer (see sections [066] to [068]) is programmed with a value other than 000. File paradox spectra 1738 user manual. user manual / Rapier V1 user manual - 2MB

Setting up G10 communicator with Protegus - Trikdis Please note that the keypad can be programmed to emit a BEEP every 5 seconds whenever a new trouble condition has occurred. [1] - No Battery or Low Battery [8] - Timer Loss** [2] - Wireless Transmitter Low Battery [9] - Tamper or Zone Wiring Failure* [3] - Power Failure [10] - Telephone Line Monitoring Failure [4] - Bell Output Disconnected [11]/[STAY] - Fire Loop Trouble* [5] - Maximum Bell Current [12]/[BYP] - Module Loss [6] - Maximum Auxiliary Current [13]/[MEM] - Wireless Transmitter Supervision Loss* [7] - Communicator Report Failure [16]/[FORCE] and [TBL]/[TRBL] flashes - Keypad Fault * press the illuminated key ([9], [STAY] or [MEM]) to view which zones are causing the trouble. When key [2] is OFF (not illuminated), EOL is disabled and the keypad zone uses the on-board EOL resistor. Failure Disabled Enabled [7] Future Use N/A N/A [8] Future Use N/A N/A * Not to be used with UL installations. 2010 2 CAPTAIN 6 User Guide SAFETY INSTRUCTIONS Your CAPTAIN-i More information Quick Start Table Of Contents Getting Started... PARADOX®. SPECTRA SP5500, SP6000, SP7000, 1727, 1728, 1738;. Using control panel`s installation manual, set locations and features of segment.

EX, 1728, 1738EX AND 1738 SYSTEM PROGRAMMING When key [1] is OFF (not illuminated), the keypad s zone is Keypad Zone 1. Section # Event # Sub- # Partition # [120] PGM 1 PGM Activation Event / / / [121] PGM 1 PGM Deactivation Event / / / PGMEX and 1738 only: [122] PGM 2 PGM Activation Event / / / [123] PGM 2 PGM Deactivation Event / / / [124] Global PGM Activation Event / / / [125] Global PGM Deactivation Event / / / Used to activate PGMs on expansion modules & LCD keypads. Refer to 1728EX, 1728, 1738EX and 1738 Reference & Installation Manual for details. Spectra 1728/EX & 1738/EX Programming Guide. SYSTEM SETTINGS USER CODE OPTIONS REPROGRAM ALL MODULES PARADOX MEMORY. Refer to 1728EX, 1728, 1738EX and 1738 Reference & Installation Manual for details.

Reference installation manual senzor cctv 4 CONFURING THE 1686H, 1686V AND 1689 KEYPADS (V2.0 OR HHER)... Does not function with sections using Feature Select Programming. [068] / / seconds (000 = follow Deactivation Event) GLOBAL PGM TIMER 5 sec. [085] / / seconds RECENT CLOSING DELAY No delay [086] / / minutes POWER FAILURE REPORT DELAY 15 min. Installation Manual Part 3 Programming Methods 3.1 WinLoad Software for Windows Program the Spectra Series control panels remotely or on-site using.

Esprit User Manual User's Manual. 1.0 BASIC OPERATION. The Esprit 616, 626, 636 and 646 keypads all function in the same way, but display the visual feedback differently.


Paradox spectra 1728 installation manual:

Rating: 91 / 100

Overall: 90 Rates